Guide · pairs with the frozen pipes checklist
No water from your well in winter? Start here
When the taps go dry on a below-zero morning, the problem is usually a short section of pipe or a small fitting that froze—not the well itself. These checks go from easiest to hardest. Use them with the frozen pipes & winterizing checklist. If the freeze is in a house pipe, see how to thaw a frozen pipe safely. This is educational—not a substitute for a licensed pump installer, well driller, plumber, or electrician.
Safety first: well pumps run on 240 volts in many homes. Keep water away from electrical boxes, don't open the pressure switch cover, and turn the pump breaker off if the pump is running but no water is coming in.
Step-by-step checks
- Check whether it is the whole house. Open a cold tap in two different rooms. If one fixture is dry but others flow, the freeze is in the pipe to that fixture (often on an outside wall), not at the well.
- Check power to the pump. Look for a tripped breaker or blown fuse labeled well or pump, and confirm the house has power. A tripped breaker is an electrical problem, not a freeze—if it trips again after one reset, stop and call a pump installer or electrician.
- Read the pressure gauge. Most systems have a gauge near the pressure tank. Near zero with the pump silent usually means the pressure switch is not calling for water—often because its small sensing tube or fitting froze. If the gauge is low and you can hear the pump running with no water coming in, turn the pump breaker off to protect the pump.
- Find the cold spot. Run your hand along exposed pipe at the pressure tank, the pressure switch, and where the water line comes through the foundation or crawl space. Frost on the pipe, or a section much colder than the rest, marks the likely freeze. Unheated well houses, well pits, and garages are common trouble spots.
- Thaw gently with safe heat. With a faucet open, warm the frozen section using a hair dryer, an electric heating pad, or a space heater kept away from anything flammable. Work from the faucet side back toward the cold spot. Never use a torch or any open flame. Keep electric devices away from standing or dripping water.
- Restore and check for damage. Once water flows, let it run a few minutes and watch for leaks or split pipe. If a pipe burst, turn off the pump breaker and close the main valve, then call a licensed plumber or pump installer.
Where well systems usually freeze
| Spot | What you'll notice | DIY or pro? |
|---|---|---|
| Pressure switch sensing tube / fitting | Gauge near zero, pump never kicks on | Gentle warming only; pro if it doesn't recover |
| Pipe where the line enters the house | Cold or frosted pipe at the foundation wall or crawl space | DIY gentle thaw if you can reach it |
| Well house, well pit, or cold garage | Exposed pipe and tank in an unheated space | DIY gentle thaw; add insulation or safe heat afterward |
| Pressure tank fittings | Tank area very cold; frost on fittings | DIY gentle thaw; pro for cracked tank or fittings |
| Buried line or pitless adapter | Nothing reachable is cold, but no water reaches the house | Licensed well contractor or pump installer |
When it isn't a freeze
- Power outage: no power means no water on a well. Generators belong outdoors, at least 20 feet from windows, doors, and attached garages (Ready.gov winter weather).
- Breaker trips again right away, pump hums but no pressure builds, or pressure cycles on and off rapidly: these point to a pump, switch, or pressure-tank problem.
- In Wisconsin, pump, pitless adapter, and pressure-tank work is done by a DNR-licensed pump installer (WI DNR “You and Your Well,” DG-002). Other states have similar rules.
Worked example
Prevent it next time
- Insulate exposed pipe, especially near the pressure tank, switch, and the line's entry point. Use UL-listed heat cable where needed and install it exactly as the label says (American Red Cross: frozen pipes).
- Seal drafts and gaps around the foundation where the water line enters.
- In an arctic cold snap, let the faucet farthest from the pressure tank drip and keep the thermostat steady day and night.
- Know where the pump breaker and the main shutoff valve are before an emergency.
- Keep up with yearly well testing—see the well water testing checklist.
FAQ
Can a buried well line freeze?
It is uncommon when the line and the pitless adapter are below the frost line, but it can happen with shallow lines, missing snow cover, or disturbed soil. A freeze you cannot reach underground is a job for a licensed well contractor or pump installer.
Should I keep resetting the pressure switch?
No. The pressure switch carries line voltage. Don't open the cover, pry the contacts, or tap the switch to make the pump run. If gently warming the switch's sensing tube doesn't bring pressure back, call a licensed pump installer.
Do I need to test my water after a frozen well line?
If any part of the well, pump, or pressure system was opened or replaced, ask the installer about disinfection and a bacteria sample. Wisconsin DNR recommends a bacteria test at least once a year and any time taste, color, or smell changes.
How do I keep my well from freezing next winter?
Insulate exposed pipe and the pressure tank area, use UL-listed heat cable installed to the maker's instructions where pipes run through cold spaces, seal drafts where the line enters the house, and let the faucet farthest from the tank drip in an arctic cold snap.
Open the frozen pipes checklist · Well water testing checklist · Propane in winter · Frozen septic system · All guides
Educational estimates only — not professional advice. Confirm with a licensed contractor, your county health department, or a certified lab.