Guide · matched to the cord of wood calculator
How much firewood do I need for winter?
Rules of thumb like “4 to 6 cords” are all over the internet, but your house isn't average. The most reliable way to size your woodpile is to start from the heat your home actually used last winter—your propane, fuel oil, or natural gas history—and convert it to cords. This guide shows the math, with worked examples. Check that a delivered stack is a real cord with the free cord of wood calculator. It is educational—not a substitute for your stove manufacturer's instructions or a chimney professional.
Step 1 — How much heat did your house use last winter?
Add up last heating season's fuel from your delivery tickets or bills, then convert it to delivered heat (what actually reached your rooms):
delivered heat = fuel used × BTU per unit × furnace efficiency
| Fuel | BTU per unit (EIA) | Typical efficiency to use |
|---|---|---|
| Propane | 91,452 per gallon | AFUE from the furnace label (often 80–95%) |
| Heating oil | 138,500 per gallon | AFUE from the label (often 80–87%) |
| Natural gas | 100,000 per therm | AFUE from the label |
| Electric resistance | 3,412 per kWh | 100% |
Heat contents: U.S. EIA. Only count fuel used for space heating—subtract a share for a propane water heater, range, or dryer (summer months show roughly how much those use).
Step 2 — How much heat a cord of wood gives you
usable heat per cord = BTU per cord × stove efficiency
- BTU per cord: the EIA uses about 20 million BTU for a cord of air-dried wood. Dense hardwoods (oak, hickory, sugar maple, ash) are at or above that; softwoods (pine, spruce, aspen, basswood) are much lower—a University of Connecticut fuel table uses about 12 million BTU per cord.
- Stove efficiency: the UConn table uses 60% for wood. A newer EPA-certified stove burning dry wood can do better; an open fireplace does far worse and can even lose heat overall.
Mixed hardwood at 20 million BTU × 60% = 12 million BTU of usable heat per cord. At 70% it is 14 million.
Step 3 — Divide, then add a buffer
cords needed = delivered heat ÷ usable heat per cord, then add 15–25% for a colder-than-normal winter, wood that isn't fully dry, and the share of the pile you won't burn efficiently (startup fires, shoulder seasons).
Worked examples
Example B — same house, newer stove
Same 57.6 million BTU, but an EPA-certified stove at about 70% → 14 million BTU per cord → 4.1 cords, or about 4.9 with a 20% buffer. Better efficiency saves roughly 0.8 cords a winter.
Example C — wood as supplemental heat
The stove covers evenings and weekends while the furnace handles the rest. Propane use dropped from 700 to 450 gal, so wood replaced 250 gal → 20.6 million BTU ÷ 12 ≈ 1.7 cords (about 2.1 with a buffer).
Example D — softwood instead of hardwood
If Example A's pile were mostly pine or aspen at about 12 million BTU per cord × 60% = 7.2 million usable, the same house would need 57.6 ÷ 7.2 ≈ 8.0 cords—over 60% more wood to stack, split, and carry.
No fuel history? Rough ranges
| How you heat with wood | Rough cords per winter (cold northern climate) |
|---|---|
| Fireplace or stove for ambiance, a few fires a week | ½–1 cord |
| Supplemental: evenings and weekends | 1–3 cords |
| Primary heat, smaller or well-insulated home | 3–5 cords |
| Primary heat, larger or drafty farmhouse | 5–8+ cords |
These are planning ranges built from the method above, not measured data. Your first winter's log is the best number you will ever have—write down every cord bought and when it ran out.
Buying and storing tips
- Buy in full cords (128 cubic feet stacked). A “face cord” or “rick” is not a standard unit—see the firewood cord pricing guide and measure delivered stacks with the cord calculator.
- Burn only dry, seasoned wood—about 20% moisture or less, checked with a moisture meter on a freshly split face (EPA Burn Wise). Most hardwood needs at least 6–12 months split and stacked to season.
- Stack off the ground, top covered, sides open to the wind, and keep the main pile away from the house.
- Have the chimney inspected and swept as needed—at least once a year, per the stove and chimney manufacturer.
- Keep a working carbon monoxide alarm and smoke alarms near sleeping areas.
- Keep the backup heat working: in a cold snap your propane tank still matters.
FAQ
How many cords of wood do I need for a winter?
There is no single number—it depends on how much heat your house needs, the wood species, and your stove. As a worked example, a home that burned 700 gallons of propane for heat in a 90% furnace would need about 4.8 cords of air-dried hardwood in a 60%-efficient stove to replace it fully. A woodstove used for evenings and weekends might need only 1–3 cords. Use your own fuel history for a real estimate.
How much heat is in a cord of firewood?
The U.S. EIA uses about 20 million BTU for a cord of air-dried wood. Dense hardwoods like oak, hickory, and sugar maple are higher than that; softwoods like pine, spruce, and aspen are lower (a University of Connecticut fuel-cost table uses about 12 million BTU per cord for softwoods).
Is a face cord enough for winter?
Usually not for primary heat. A full cord is 128 cubic feet (4 × 4 × 8 ft). A “face cord” has no legal definition and is often one 16-inch-deep row, about one-third of a cord. Price and plan in full cords—see the firewood pricing guide.
When should I buy firewood for winter?
Ideally a year ahead, so it has time to season. Wet wood wastes much of its heat boiling off water and makes more smoke and creosote. EPA Burn Wise recommends burning only dry, seasoned wood, around 20% moisture or less.
Open the cord of wood calculator · Firewood pricing guide · Propane in winter · All guides
Educational estimates only — not professional advice. Confirm with a licensed contractor, your county health department, or a certified lab.